What F10 means on your Asko dryer (asko dryer f10)
An asko dryer f10 problem is the TD70.1 Type B panel’s label for a full condensate tank whose microswitch has opened, stopping the cycle before the tank can overflow. This F10 belongs only to the dryer, and only to this particular board revision — it is worth saying plainly because Asko also uses F10 on dishwashers (an overfilling-water problem) and on washers (an overfilling problem too), and none of the three share any cause or fix. On the dryer’s own TD70.1 Type A predecessor, this identical tank-full event displays as L4 instead, so the code alone does not tell you which board is fitted without checking the panel style.
Symptoms
Before booking, check the behavior of your Asko dryer against the points below, because several unrelated problems overlap in how they present. The dryer may show one symptom or many together, developing slowly across cycles or striking suddenly after an outage, a spill, or an installation change.
- The display shows F10 and the cycle pauses or stops
- The condensate tank feels heavy or is visibly full when pulled out
- The dryer resumes normally once the tank has been emptied
- F10 recurs at roughly the same point in successive cycles with heavy loads
Common causes
The causes below all produce similar symptoms on an Asko dryer, so the order matters — start at the top where the odds are highest. That approach tells you fast whether your dryer needs a two-minute check or a repair with genuine parts and an experienced hand.
- Condensate tank genuinely full — expected behavior; larger or wetter loads fill the tank faster
- Tank not fully seated — an incompletely inserted tank can leave the microswitch open even when the tank is not full
- Worn or dirty microswitch contacts — residue buildup can cause a false full reading
- Blocked optional drain hose — on units plumbed to drain directly, a kink or clog can prevent the tank from draining as intended
Troubleshooting steps you can try
Go through the steps on your Asko dryer from top to bottom before booking a repair, since the early ones cover the common causes. The moment mains voltage, gas, a hot cavity, water, or a sealed component enters the picture on the dryer, hand the job to a qualified technician.
- Remove the condensate tank and empty it completely.
- Clean the tank rim and cabinet opening before reinserting.
- Push the tank all the way in until it seats flush and clicks.
- Restart the program and confirm F10 clears.
- Check any connected drain hose for kinks if the tank is emptying itself correctly but F10 still appears often.
Parts a technician may replace
A technician may inspect, test, or replace the condensate tank, tank microswitch, and drain hose (where fitted) on your Asko dryer once the cause is clear. Confirming which of these has actually failed on the dryer before ordering keeps the repair tight, and the replacement is matched by model, serial, and Art. No. for an exact fit.
When to call a technician
F10 that returns right after a correctly reseated, empty tank needs an experienced technician to test the tank microswitch on your TD70.1 Type B dryer. A Low-severity rating means no emergency for your Asko dryer, but F10 reappearing on the dryer after the checks above should be confirmed by a technician before anything is replaced. We are not affiliated with Asko, Gorenje, or Hisense; your dryer is repaired independently by experienced technicians with genuine OEM or trusted-supplier parts and a 30-day labor warranty. Have your Asko dryer’s rating-plate details — model, serial, and Art. No. — ready at booking so the exact part for the dryer is sourced in advance and F10 is cleared efficiently.
Related help and Asko resources
For a persistent F10 on your Asko dryer, book Asko dryer repair, read our other dryer error-code guides, follow the step-by-step repair guides, schedule service whenever works for you, or check your city on our locations page. See also L4 condensate tank full, which is related to this problem on your Asko dryer. Complete model and specification details for your Asko dryer can be checked at the maker’s site, us.asko.com.
