What F0-F6 means on your Asko cooktop (asko cooktop f0 f6)
F0 through F6 sit together on the F-series induction family (HI1655M and related boards), and Asko’s manual assigns every one of these seven display numbers the same cause: the ambient temperature is not good. In practice that means a heat source near or under the cooking plate is affecting the generator’s temperature reading, not that seven different parts have failed. This is an environmental problem rather than a component problem, which is why the manual’s fix is a single sentence: switch off all heat sources near the cooking plate. If the exact digit shown is not F00, F7, F8, F9, F99, FA or FAN, treat it as belonging to this ambient-temperature group.
Symptoms
To be sure your Asko cooktop has this problem and not a close relative, line up what you are seeing against the signs below. On the cooktop these can show up singly or several together, easing in over time or arriving suddenly after an outage, a spill, or a service visit.
- The display shows a two-digit code beginning with F, somewhere in the F0-F6 range, during or shortly after cooking.
- The problem often appears when an oven below the hob or an adjacent appliance has been running hot.
- Zones may pause or refuse to reach the selected power level while the code is showing.
- The code clears on its own once the surrounding area has cooled.
Common causes
The causes below all produce similar symptoms on an Asko cooktop, so the order matters — start at the top where the odds are highest. That approach tells you fast whether your cooktop needs a two-minute check or a repair with genuine parts and an experienced hand.
- An oven running directly underneath the hob — heat rising from below raises the temperature the generator’s sensor reads.
- A dishwasher or other heat-producing appliance installed next to the hob — proximity heat affects the same sensor.
- Poor clearance in the cabinetry around the hob — insufficient gap traps heat instead of letting it dissipate.
- A pan left on a zone with residual heat while another appliance nearby is also running — combined heat load pushes the reading past the generator’s comfortable range.
Troubleshooting steps you can try
Before you call for service, try each step on your Asko cooktop in turn and watch how it responds. If a step on the cooktop takes you near mains wiring, gas, a hot oven cavity, water, or a sealed component, stop and pass it to a qualified technician.
- Switch off any oven, warming drawer, or other heat-producing appliance installed directly under or beside the hob.
- Remove any pan or object holding residual heat from the affected zone.
- Wait several minutes for the surrounding cabinetry to cool before retrying the zone.
- Check that the ventilation gap specified in the installation instructions under the hob has not been closed off.
- Retry the zone once the area has cooled; the code should not return under normal conditions.
- If the code returns with no nearby heat source running, the generator’s temperature sensor itself may be responsible and needs a technician.
Parts a technician may replace
A technician may inspect, test, or replace the generator temperature sensor and surrounding cabinetry ventilation on your Asko cooktop once the cause is clear. Confirming which of these has actually failed on the cooktop before ordering keeps the repair tight, and the replacement is matched by model, serial, and Art. No. for an exact fit.
When to call a technician
A technician measures the generator sensor’s reading against ambient temperature to separate a genuine installation heat problem from a sensor that is misreading on its own. A Low-severity rating means no emergency for your Asko cooktop, but F0-F6 reappearing on the cooktop after the checks above should be confirmed by a technician before anything is replaced. Your Asko cooktop is serviced by an independent team with no affiliation to Asko, Gorenje, or Hisense, relying on experienced technicians and genuine OEM or trusted-supplier parts backed by a 30-day labor warranty. Have the model, serial, and Art. No. from your Asko cooktop ready when you schedule, and the correct component can be matched to your cooktop beforehand so F0-F6 is resolved in one trip where possible.
Related help and Asko resources
A F0-F6 that keeps coming back on your Asko cooktop is worth a proper look: book Asko cooktop repair, scan our other cooktop error-code guides, use our step-by-step repair guides, schedule service for an appointment, or check your area on our locations page. Look up your Asko cooktop on the manufacturer’s own pages at global.asko.com for full specifications.
